鋁卷是一種使用范圍很廣泛的鋁制品，在各行各業都可以看到它的身影，為了保證該產品的使用效果，在加工和使用的過程中都應嚴格遵守相關的規則。下面鋁卷廠家就為您介紹一下它的加工和使用注意事項吧。
Aluminum coil is a widely used aluminum product that can be seen in various industries. To ensure the effectiveness of the product, relevant rules should be strictly followed during processing and use. Below, the aluminum coil manufacturer will introduce its processing and usage precautions to you.
1、安裝方向：銅色鋁卷安裝在同一個平面上時，工藝方向應該一致。否則，可能會(huì )出現視覺色差。
1. Installation direction: When installing copper colored aluminum coils on the same plane, the process direction should be consistent. Otherwise, visual color difference may occur.
2、缺口：使用槽或鑼機開槽時，應選取半圓形頭型大于90度的銑刀。底刀不要把鋁卷傷得太深或折得太淺，要把0.2-0.3毫米厚的塑料芯和鋁板彎曲在一起，以提高強度和韌性。否則，彎曲時鋁卷會(huì )破裂或薄膜會(huì )爆炸
2. Notch: When using a slot or gong machine for slotting, a milling cutter with a semicircular head shape greater than 90 degrees should be selected. Do not damage the aluminum coil too deeply or fold it too shallow with the bottom knife. Bend the plastic core and aluminum plate with a thickness of 0.2-0.3mm together to improve strength and toughness. Otherwise, the aluminum coil will break or the film will explode during bending
3、使用條件：內壁板要在室內使用，不能設置在室外，以保證使用效果和使用壽命。

3. Usage conditions: The inner wall panel should be used indoors and cannot be set outdoors to ensure its effectiveness and lifespan.
4、要運輸：搬運板材，應同時舉起板的斜面，嚴禁推或萃取，以免刮傷板面。
4. To transport: When handling the board, the inclined surface of the board should be lifted at the same time, and pushing or extracting is strictly prohibited to avoid scratching the board surface.
5、弧形加工：鋁卷廠家在加工圓弧時應使用特殊彎曲設備進行加工，慢慢施力，使卷材逐漸達到所需表面，不要一次性彎曲。
5. Arc machining: Aluminum coil manufacturers should use special bending equipment to process the arc, slowly apply force to gradually reach the required surface of the coil, and do not bend it at once.
6、撕裂膜：應在安裝鋁卷后45天內撕開保護膜。否則，可能會(huì )出現撕裂困難或轉移粘合劑的現象。
6. Tearing film: The protective film should be torn off within 45 days after installing the aluminum coil. Otherwise, difficulties in tearing or transfer of adhesive may occur.
7、保管：要將鋁卷存放在干燥通風中，平放在平整表面，不要踩踏或碰撞。
7. Storage: The aluminum coils should be stored in a dry and ventilated place, flat on a flat surface, and do not step or collide.
8、布局：等型號和其他布局的卷材可能會(huì )有色差。銷售和使用不同批量的板材時，應增加比較色差程序。只有在沒有視覺色差的情況下，才能在同一個平面上使用。
8. Layout: There may be color differences between coil materials of different models and other layouts. When selling and using different batches of boards, a color difference comparison program should be added. Only when there is no visual color difference can it be used on the same plane.